How to Make a Wine Glass Rack That Fits Your Cabinets
Posts by Claire DonovanNovember 20, 20260 Comments
19 min read · by Claire Donovan · Updated
We may earn a commission when you buy through links on this page, at no extra cost to you. Learn more.
To learn how to make a wine glass rack, build a set of wooden T-shaped rails, space them to support your glasses by their bases, and securely attach them underneath a kitchen cabinet. A wooden under-cabinet rack makes use of otherwise wasted space while keeping stemware organized and accessible. With hardwood boards, wood glue, screws, and basic woodworking tools, you can create a practical rack sized for your own collection. The most important considerations are accurate measurements, appropriate rail spacing, and secure mounting.
A homemade wine glass rack can be a straightforward weekend woodworking project, whether you want to organize a small collection of everyday glasses or display special Bordeaux glasses, Chardonnay glasses, and champagne flutes. The design described here uses five parallel wooden rails to create four storage channels. Each glass slides into a channel by its base, leaving the bowl and stem hanging underneath. You can adjust the overall dimensions to suit your cabinets, available headroom, and preferred glass styles.
Choose the Right Design and Measure Your Glassware
A successful wine glass rack starts with the glassware rather than the lumber. Measure your largest glass bases, bowl widths, stem lengths, and overall heights before deciding how large the finished rack should be. A few minutes of measuring can prevent a finished rack from being too narrow, too shallow, or incompatible with your favorite glasses.

The most practical design for a kitchen cabinet is an under-cabinet wooden stemware rack. It consists of five parallel rails, each made from a wide bottom strip and a narrower spacer glued onto its upper surface. This creates channels that capture the glass feet while leaving the stems free to hang underneath. The arrangement is relatively simple to construct and can be customized for different cabinet widths.
Begin by selecting the location. A cabinet above a serving counter, home bar, or kitchen preparation area is usually convenient. Measure the available width and depth of its underside. Also measure the distance between the bottom of the cabinet and the countertop, including any appliances that normally sit below it.
Next, measure the largest glass in your collection. Pay particular attention to its base diameter because the base must slide into the opening between the rails. Measure the widest bowl too, since neighboring bowls need enough room to hang without touching.
Consider these practical starting measurements:
- Rack width: Approximately 19 5/8 inches for a medium-sized installation.
- Rack depth: Approximately 11 inches for a standard four-row arrangement.
- Rack height: Approximately 1 1/2 inches for a surfaced-four-sides wooden construction.
- Stem slot: Approximately 1 inch between neighboring bottom strips in the referenced design.
- Glass clearance: Allow approximately 1/2 to 1 inch between neighboring stored glasses wherever their shapes permit.
These are reference dimensions, not universal requirements. A collection dominated by large Burgundy glasses may need different clearances from one containing narrow white-wine glasses or champagne flutes. If your glass bases are unusually large, test a sample channel before cutting all five rails.
Think about the direction in which you will insert and remove the glasses. A front-loading rack allows you to slide each glass into position from the cabinet’s front edge. Leave enough room for your hand to grip the stem without striking the neighboring glass or the cabinet door.
For additional design inspiration, compare the dimensions and construction of a traditional wooden wine rack. Although a bottle rack supports bottles horizontally, many of the same woodworking principles apply to cutting, sanding, finishing, and assembling a wooden storage structure.
Gather the Wood, Hardware, and Tools
Hardwood is a dependable choice for a wooden wine glass rack because it holds screws well and provides a durable surface. Prepare five matching bottom strips, five narrower spacer strips, suitable mounting screws, and wood glue. Having all components ready before assembly makes it easier to keep the rails straight and evenly spaced.
Maple, oak, cherry, and walnut are suitable options. Maple offers a light, relatively uniform appearance, while walnut provides a darker finish that can complement traditional bar furniture. Cherry has a warm natural color that develops a deeper appearance over time. Choose straight, dry boards without significant cracks, twisting, or loose knots around the planned screw locations.
For a straightforward surfaced-four-sides design, the following cut list provides a useful starting point. The dimensions are based on a published five-rail woodworking plan and are intended as a reference for a medium-sized installation. The under-cabinet wine glass rack woodworking plan provides additional construction details and alternative lumber dimensions.
| Component | Quantity | Length | Width | Thickness |
|---|---|---|---|---|
| Bottom strips | 5 | 11 inches | 3 1/8 inches | 3/4 inch |
| Spacer strips | 5 | 11 inches | 3/4 inch | 3/4 inch |
| Assembled rails | 5 | 11 inches | 3 1/8 inches | 1 1/2 inches |
| Mounting screws | 15 | 1 1/4 inches | #8 gauge | As specified |
The completed arrangement measures approximately 19 5/8 inches wide, 11 inches deep, and 1 1/2 inches tall. The five rails create four storage rows. You can reduce the width for a smaller cabinet or increase it if your cabinet and glass collection require additional room.
For the woodworking process, gather the following equipment:
- A table saw or circular saw with a suitable cutting guide.
- A miter saw or circular saw for crosscutting.
- A drill and driver with appropriate drill bits.
- A countersink bit and counterbore bit.
- Woodworking glue suitable for hardwood.
- Four to six clamps for holding the glued components.
- 120-, 180-, and 220-grit sandpaper.
- A measuring tape, pencil, square, and straightedge.
- Wood finish, such as wipe-on oil or water-based polyurethane.
Use straight-grained lumber and make sure the boards have consistent thickness. Uneven pieces can produce rails that sit at different heights, making glass insertion awkward. If you are purchasing surfaced lumber, choose boards that are already flat and square to reduce preparation work.
Do not overlook the mounting hardware. Fifteen #8 x 1 1/4-inch screws are specified for the reference five-rail design. These dimensions are appropriate to that particular construction, not automatically suitable for every cabinet. The screw length and installation direction must account for both the rail construction and the thickness of the cabinet material.
Tip: Make one complete sample rail before preparing the remaining four. Test it with your largest glass base, confirm the channel opening, and check that the glass slides smoothly without becoming loose.
Cut and Assemble the Five Wooden Rails
The main construction task is making five matching T-shaped rails. Each rail consists of a wide bottom strip with a narrower spacer attached on top, creating a channel that holds the glass base. Accurate cutting, consistent glue joints, and properly aligned edges are more important than decorative details.
Start by marking the bottom strips and spacer strips on your lumber. For the reference design, each bottom strip measures 11 inches long, 3 1/8 inches wide, and 3/4 inch thick. Each spacer measures 11 inches long, 3/4 inch wide, and 3/4 inch thick.
Cut five pieces of each component. If you are working from wider boards, rip the lumber into strips first and then crosscut each piece to length. Use a stop block when possible so all ten components have matching lengths.
When operating a table saw, use a push stick for narrow cuts and keep your hands away from the blade. Wear eye and hearing protection, support the workpiece properly, and avoid forcing the wood through the saw. If you do not have the appropriate equipment or experience, have the lumber cut by a qualified woodworking shop.
Position the spacers correctly
Three of the five rails are middle rails. Their spacers should be centered across the bottom strips. The remaining two rails form the outside boundaries of the rack, so their spacers should sit flush with their respective outside edges.
This arrangement creates the required openings between neighboring rails while giving the outer edges a finished appearance. Lay all five assemblies on a flat work surface before applying glue. Check that the three middle spacers are centered and that the outside spacers face the correct directions.
Apply an even layer of woodworking glue to the mating surfaces. Position each spacer carefully, keeping its ends flush with the bottom strip. Clamp the components firmly enough to maintain contact without squeezing out excessive glue or causing the strips to shift.
The long-grain-to-long-grain arrangement creates a substantial glue surface. Follow the adhesive manufacturer’s recommended clamping and curing times. Allow the joints to cure fully before sanding or drilling mounting holes.
Prepare the channels and screw holes
Once the glue has cured, inspect every rail. Remove dried glue residue and check for uneven edges. The long edges of the bottom strips should be comfortable to handle, without sharp corners that might catch a glass stem.
Use a 1/8-inch roundover bit or a sanding block to soften the exposed edges. Avoid removing too much material because the dimensions of the channels are important for retaining the glass bases.
Next, mark three screw positions along each spacer. For the reference construction, the holes are positioned approximately 1 inch from each end and one in the middle. Drill counterbores from the underside of the bottom strips, then drill smaller pilot holes through the remaining material.
Counterbores allow the screw heads to sit below the surface and provide enough depth for the screws to pass through the rail assembly. Follow the specified depth for your chosen lumber thickness. The objective is to create a secure attachment without weakening the spacer or allowing a screw to protrude into the cabinet interior.
Before proceeding, dry-fit the five rails together on a flat surface. Check that their lengths match, their outside edges align, and the channels remain consistent from front to back. Correct small discrepancies now rather than after mounting.
Set Rail Spacing for Different Wine Glass Shapes
Rail spacing determines whether your wine glasses slide into the rack easily and remain supported during storage. The correct dimensions depend on the diameter of the glass foot, the width of the stem, and the shape of the bowl. Measure your own collection instead of assuming every wine glass follows standard dimensions.

For the five-rail design, the published plan uses approximately 1-inch stem slots between neighboring bottom strips. The assembled rails form four rows, with the reference version placing the rows approximately 4 1/8 inches apart. These dimensions provide a useful starting point for many conventional stemmed glasses.
However, not every wine glass has the same base dimensions. A narrow sparkling-wine flute may have a relatively small base, while a large red-wine glass can have a broad foot and an oversized bowl. Both need sufficient room to slide into the channel and hang without touching adjacent glasses.
Measure the base diameter of at least three representative glasses: your smallest, largest, and most frequently used. Also check the widest part of their bowls. A rack that accommodates the smallest glass may still cause collisions when filled with larger Bordeaux or Burgundy styles.
Understand the relationship between the rails
The glass foot must remain supported by the neighboring rails while the stem hangs through the opening. The channel needs to be wide enough for the foot to slide into position but narrow enough to retain it securely.
One way to establish the correct spacing is to assemble two sample rails and place them beneath a piece of scrap wood or a temporary mounting board. Slide a representative glass into the opening. Check whether the base moves freely and whether the bowl hangs without contacting the surrounding structure.
Repeat the test with your widest and narrowest glasses. If the foot cannot enter easily, adjust the opening. If the foot slips through or becomes unstable, reduce the opening or select a different rail design.
For another approach to spacing, Weekand’s instructions for building a wine glass hanging rack recommend measuring the largest glass base first. Its example uses T-molding spaced slightly more than 2 inches on center for glasses with 2-inch-diameter bases.
Also consider the spacing between the centers of the individual glasses. Wine Enthusiast recommends leaving approximately 1/2 to 1 inch between stored glasses to reduce the risk of accidental collisions. This is particularly important for delicate crystal stemware and large bowls.
For example, a collection of broad Burgundy glasses may require fewer positions than a collection of slim champagne flutes. Staggering neighboring glasses can sometimes improve clearance, but the arrangement should never force bowls into contact.
Compare the dimensions of different glassware
The following examples illustrate why testing actual glasses is important. The figures are practical planning illustrations, not universal manufacturer specifications.
| Glass style | Typical design consideration | Rack planning priority |
|---|---|---|
| Champagne flute | Narrow, elongated bowl | Check foot retention and stem clearance |
| Pinot Noir glass | Broad, rounded bowl | Allow additional bowl clearance |
| Bordeaux glass | Tall bowl with substantial capacity | Check hanging height and neighboring bowls |
| Chardonnay glass | Medium-width bowl | Test base diameter and channel opening |
| Universal wine glass | Moderate bowl dimensions | Check the largest glass in the collection |
Pay attention to the available clearance below the cabinet too. A glass that fits the rack horizontally might still hang too close to a coffee machine, countertop appliance, or frequently used preparation area.
Before permanently attaching the rails, insert several glasses and inspect the arrangement from the side and front. Make sure each glass is independently supported and can be removed without lifting or striking its neighbors.
Sand, Finish, and Protect the Wooden Rack
A smooth, properly finished wooden rack is easier to clean and more attractive than unfinished lumber. Sanding removes rough edges, while an appropriate protective coating helps reduce moisture absorption and staining. Finish the rails before mounting them so you can reach all exposed surfaces.
Begin with 120-grit sandpaper to remove saw marks and minor irregularities. Move to 180-grit to refine the surface, then finish with 220-grit for a smoother appearance. Sand in the direction of the wood grain, paying particular attention to the channel edges where glass bases will slide.
Inspect the assembled rails under good lighting. Look for glue residue, splinters, rough spots, and uneven corners. A small amount of additional sanding is preferable to leaving an area that could scratch a glass foot or catch a cleaning cloth.
Select a suitable wood finish
Several finishes work well for indoor furniture projects. Wipe-on oil can emphasize the natural grain, while water-based polyurethane creates a more protective surface with a relatively clear appearance. Hardwax oil is another option for a natural-looking finish.
Follow the product instructions carefully, including application thickness, ventilation requirements, drying periods, and curing times. Apply two to three coats when recommended by the finish manufacturer, allowing the appropriate drying time between applications.
Do not install wine glasses while the coating remains tacky or produces noticeable fumes. A finish that feels dry on the surface may still need additional curing time before regular use. Allow the complete assembly to cure according to the product instructions.
Choose the finish based on the appearance of your cabinets and the amount of moisture exposure the rack is likely to receive. A natural walnut rack can look attractive beneath light cabinets, while a painted maple rack can blend into white or cream-colored kitchen furniture.
For a painted finish, apply a suitable primer where required and use a durable interior coating. Lightly sand between coats if the manufacturer recommends it. Keep the channel openings free from excess paint because thick buildup can interfere with glass insertion.
Consider the location when choosing a finish
A wine glass rack should be installed away from direct cooking splashes, excessive grease, and persistent moisture. A location immediately above a stovetop is less suitable because cooking residue can collect on exposed glassware.
Likewise, avoid placing unfinished wood near a sink where frequent splashes could cause discoloration or swelling. A suitable protective finish helps, but it does not make wood waterproof.
For a decorative touch, you can round the visible ends of the rails slightly, use matching wood plugs over visible fasteners, or stain the wood to coordinate with existing furniture. Keep decorative features away from the glass-supporting channels.
If you have leftover wine corks from entertaining, another small woodworking project is making a cork board from wine corks. It can complement a homemade wine glass rack and provide a convenient place for tasting notes or reminders.
Mount the Rack Securely Under the Cabinet
Proper mounting is essential because the rack will hold fragile glassware above a working surface. Use appropriate screws, predrill the mounting holes, and verify that the cabinet material can support the assembly. Never assume that decorative cabinet panels or thin particleboard will hold screws as securely as solid wood or suitable plywood.
Start by inspecting the underside of the cabinet. The referenced woodworking plan recommends a minimum thickness of 5/8 inch for its standard upward-screw installation. Measure the actual material rather than estimating its thickness from the cabinet’s outside appearance.
For a suitable solid wood or plywood cabinet bottom, position the first outside rail underneath the cabinet. Align its front edge with the front of the cabinet, unless your measurements call for a small setback. Hold it firmly in position and mark the mounting points.
Use a drill bit with a depth stop so the pilot holes do not penetrate the cabinet interior. A piece of tape around the drill bit can serve as a simple visual depth indicator, although a proper depth-stop attachment provides more consistent control.
Drive the mounting screws through the predrilled holes. Do not overtighten them, because excessive force can damage the wood or strip the threads. The rail should sit firmly against the cabinet without visible gaps or movement.
Install the remaining rails consistently
Once the first rail is secure, use two identical 1-inch spacer blocks to position the next rail. These temporary blocks help maintain consistent channel spacing across the assembly.
Attach the second rail, then repeat the process for the remaining middle rails and the opposite outside rail. Check each opening before tightening the screws completely. The five rails should remain parallel, with four consistent storage rows.
Measure the spacing at both the front and back. If a rail shifts during installation, loosen its screws slightly and realign it. A small difference in spacing can make glasses difficult to insert or cause their bases to sit unevenly.
If the cabinet bottom is too thin for upward mounting, the referenced woodworking plan describes an alternative approach: predrill from inside the cabinet and drive suitable screws downward into the solid hardwood spacers. This method requires careful screw-length selection and sufficient access to the cabinet interior.
Particleboard presents additional challenges because screw-holding strength can vary significantly with its condition and thickness. Do not rely on an improvised screw arrangement if the material is damaged or unsuitable. Choose a mounting method specifically designed for the cabinet construction, or have a qualified installer assess the attachment.
Test the completed installation
After installation, inspect all fifteen mounting points. Check that the screw heads are seated properly, the rails are aligned, and there is no visible movement when moderate hand pressure is applied.
Do not immediately fill the rack with your entire collection. Begin with one sturdy glass and confirm that its base remains supported. Add a few more glasses gradually, checking for movement, loose fasteners, or contact between neighboring bowls.
The reference five-rail design estimates approximately 4 pounds of glassware when fully loaded and advises against storing heavy glassware or decanters on the rack. Treat that figure as a design-specific estimate rather than a certified load rating for your own installation. The strength of the cabinet, screws, lumber, and workmanship all affect the actual capacity.
Store, Clean, and Maintain Your Wine Glass Rack
Once the rack is installed, good storage habits help preserve both the wooden construction and the glassware. Always put away clean, completely dry glasses, distribute them evenly across the available channels, and inspect the mounting hardware periodically.
Hanging storage works particularly well for stemmed glasses because the base rests in the wooden channel while the bowl hangs below. It also frees up shelf space and makes frequently used glassware easy to identify. The arrangement is especially convenient in a small home bar or kitchen where cabinet storage is limited.
However, hanging storage is not appropriate for every type of glass. Stemless wine glasses, tumblers, and many specialty tasting glasses do not have a foot that can engage the rack. Keep these on a conventional shelf or in a suitable cabinet.
Prepare glasses before putting them away
Wash glasses using a method appropriate for their material and construction. Dry them thoroughly before placing them on the rack. Remaining water can leave marks on the glass and expose the wooden surfaces to unnecessary moisture.
When handling delicate crystal, hold the bowl and base carefully rather than twisting the stem. The stem is a relatively vulnerable part of the glass, especially when the bowl is large. Slide each glass gently into its channel and avoid forcing a base past a tight opening.
It is also useful to arrange glasses by type. Keep champagne flutes together, everyday white-wine glasses in another row, and larger red-wine glasses in a separate area if the dimensions permit. This organization makes it easier to select the appropriate vessel for different wines.
If you are unsure which shapes belong in your collection, the guide to which wine glass to use for which wine explains the differences between common glass styles and their intended uses.
Maintain the wood and mounting hardware
Dust the rack regularly using a soft, dry cloth. If a glass breaks nearby, remove the remaining glassware before cleaning the channels thoroughly. Inspect the wood for splinters or damaged finish and avoid using excessive water on the assembly.
Periodically check the mounting screws for loosening. This is especially important if the cabinet experiences frequent vibration from closing doors or nearby appliances. If you notice a rail moving, remove the glassware and correct the attachment before using the rack again.
Look for signs of water damage, cracks, or splitting around the screw locations. Small surface scratches may be addressed with appropriate sanding and refinishing, but structural damage around mounting points requires more careful attention.
Keep the rack away from areas where people regularly reach across the countertop. Glass bowls hanging below a cabinet can be vulnerable to accidental contact from hands, kitchen equipment, or other objects.
Finally, avoid treating a stemware rack as general-purpose storage. Its construction is intended for compatible glasses, not bottles, heavy serving dishes, or large decanters. Keeping the intended load modest helps protect the installation and the glassware.
Frequently Asked Questions
Can you make a wine glass rack without a table saw?
Yes. A circular saw with a straight cutting guide can produce the long strips needed for a wooden rack. A miter saw or carefully guided circular saw can handle the crosscuts. A local lumber shop can also prepare the pieces if you do not have suitable cutting equipment.
Can a wine glass rack hold stemless glasses?
No. A conventional hanging stemware rack relies on the glass foot and stem to support the vessel. Stemless glasses lack this structure, so a flat shelf, cabinet organizer, or padded storage tray is a better option.
Which wood is best for a decorative wine glass rack?
Walnut, cherry, maple, and oak are popular choices for indoor furniture projects. Their grain patterns and natural colors offer different decorative effects. Select lumber that is dry and straight rather than choosing solely by appearance.
Can a wine glass rack be installed on a wall instead of a cabinet?
Yes. A wall-mounted design can use wooden support rails or a dedicated metal stemware system. The attachment must engage suitable wall framing or hardware rated for the wall construction. The mounting orientation and support arrangement should be designed specifically for the wall rather than simply reusing cabinet screws.
How do you prevent dust from collecting inside stored wine glasses?
A hanging rack stores glasses upside down, which helps limit dust entering the bowls. However, the glass openings are not sealed, so a clean storage area still matters. A cabinet with doors provides additional protection for glassware that is used infrequently.
Building a wine glass rack is a practical woodworking project that combines useful storage with a personalized decorative feature. Measure your glassware carefully, construct five consistent rails, and use an appropriate mounting method for your cabinet. With proper spacing, a smooth finish, and regular inspection, your homemade rack can provide convenient storage for everyday stemware and special-occasion glasses alike.
More in Wine Basics
Which Rose Is Best for Your Taste, Budget, and Food PairingsUpdated Nov 21, 2026
Is Cheap Wine Bad? How to Find Bottles Worth DrinkingUpdated Nov 21, 2026
What To Write On A Wine Gift Tag: Thoughtful Messages For Every OccasionUpdated Nov 21, 2026
Which Wine Is Best For Weight Loss? Compare Lower-Calorie ChoicesUpdated Nov 21, 2026
What Is The Best Wine For Mimosas? Choose Bubbly That Balances Orange JuiceUpdated Nov 20, 2026
Which Prosecco Is Best for Your Taste and OccasionUpdated Nov 20, 2026